Manuals
KLANG:app 6.1 Preview: Limiter & Ambience Ducker
This page describes the two dynamics stages of the KLANG:kontroller in KLANG:app / KOS 6.1: the ambience ducker, which pulls the ambience mic down while the mix is playing, and the safety limiter, which keeps dangerous peaks away from the musician’s ears. It is written for testers of the 6.1 preview and goes through what each stage does, why it exists, where every control lives, which values are possible and what to watch out for.
What the :kontroller adds
A KLANG:kontroller with KOS 6.1 has two dynamics stages, both running on the :kontroller itself:
| Stage | What it does | Why it is there | Where it acts |
|---|---|---|---|
| Ambience ducker | Pulls the ambience mic down while the mix on the Dante input is playing and lets it back in between songs. | During a song the ears stay clean, between songs the musician hears the room, the band and the audience. | On the ambience mic only, before it is mixed with the Dante and Aux inputs. |
| Safety limiter | Brickwall limiter that stops anything from leaving the outputs above a ceiling. | Hearing protection: a faulty device anywhere upstream can fire a full-scale burst. The limiter catches it before it reaches the ears. | At the very end of the :kontroller’s outputs. |
Other KLANG processors do not have these stages. KLANG:app in demo mode has a safety limiter of its own behind the mix (see Safety limiter in demo mode). A device whose KOS does not have a stage never shows the controls for it.
Neither stage changes the sound of a device that has never touched them: the ducker is off by default, and the limiter, which is on by default, only keeps the output below a set ceiling, which does not change the sound of a normally levelled mix. Updating to 6.1 therefore changes nothing you hear until you switch the ducker on.
The two stages share three places where you control and watch them:
CONFIG > CONNECTin KLANG:app, sectionsAmbience DuckerandSafety Limiter, to set them up.- The
AMB/AUXpage of the :kontroller, where the musician sees (and, if allowed, adjusts) them. CONFIG > INFOand theMETERscreen, to see them working.
Ambience ducker
What it does and how it listens
The ambience ducker pulls the ambience mic down while the mix is playing. In a song the ears stay clean. Between songs the ambience opens up again, so the musician hears the room, the band and the audience.
It listens to the Dante input of the :kontroller, that is the mix that arrives from the console or the processor, and not to the ambience mic itself. When the Dante input gets louder than the Threshold (dBFS), the ambience mic is pulled down by Max Ducking (dB). When the mix gets quiet, the ambience comes back. Kick and bass are filtered out of what the ducker listens to (a high-pass at 150 Hz inside the detector only), so the ambience does not pump on every bass note. The mix the musician hears is not filtered.
- Only the ambience mic is changed. The Dante input and the Aux input pass unchanged.
- Wherever the ambience mic is routed it is ducked, including an XLR or Dante output that carries
Amb Miconly. There is no way to route a raw, un-ducked ambience mic to an output while the ducker is on. - With a stereo mix the louder of the two sides decides, so the ambience image does not shift when only one side of the mix is loud.
The ducker has a fixed depth (what you set as Max Ducking (dB)), with no ratio and no knee.
Setting it up in KLANG:app
The ducker is set per mix on CONFIG > CONNECT, section Ambience Ducker, while KLANG:app is connected to a :kontroller. The section is not shown in PERSONAL mode and not for devices without a ducker. Every change is applied and stored at once, there is no Save step.
| Setting | What it does | Values |
|---|---|---|
Ducker | Switches the ambience ducker on for this mix. | on/off, default off |
Max Ducking (dB) | How far the ambience mic is pulled down while the mix is playing. It has no OFF position: only the Ducker switch turns the ducking on and off. | -60 dB to -0.5 dB in steps of 0.5 dB, default -12 dB |
Threshold (dBFS) | From which level of the Dante input on the ambience is ducked. Higher means only loud passages duck it, lower means almost anything does. | -80 dBFS to 0 dBFS in steps of 0.5 dB, default -40 dBFS |
Ducker Defaults | Reset puts this mix’s ducking (depth -12 dB, threshold and the timing behind them) back to the factory settings. The Ducker switch stays as it is. | button |
Max Ducking sets how much the ambience is pulled down. Threshold decides when that happens at all. Turning up Max Ducking (dB) does not make the effect fade in as the mix gets louder, the threshold does that job.
The timing is set at the factory and is not on this screen: the ambience is pulled down within about 30 ms, held for 300 ms after the mix gets quiet and comes back over about 800 ms. Switching the ducker off does not cut the ambience back in. It comes back smoothly, the same way it does after a song.

Max Ducking (dB) -12 dB, Threshold (dBFS) -40 dBFS, timing as above) are starting points, not tuned values. The request behind the feature was a depth of about 10 to 15 dB, so keep Max Ducking (dB) between -10 dB and -15 dB to begin with. The right Threshold (dBFS) depends on how hot the console feeds the :kontroller. If the ambience never comes back between songs, raise it. If it is never ducked during a song, lower it.Saved with the mix
The ducker settings belong to the mix of the :kontroller. They are saved in its personal presets and in its autosave, so they survive a restart. A preset without ducker settings (for example one saved before 6.1) switches the ducker off.
On the :kontroller
The AMB/AUX page of the :kontroller shows the current ducking as a bar on the AMB MIC tile, in the single pixel row between the two meter lines. It grows from the right. A full-width bar means 30 dB, deeper settings hold the bar at full width.
By default the musician cannot change the ducker. Switch on CONFIG > SETTINGS > UI Settings > Musician May Adjust Ducker to hand it over (offered only when the :kontroller has the ducker; also in CONFIG > INFO > Set Menu, and on the :kontroller itself as Ducker Control under CONFIG > Options). Then:
- On the
AMB/AUXpage pressCONFIG. The LED blinks and the tiles that have a page readEDIT. - Push the
AMB MICtile. Its page hasBACK, the ambience level with its meters and the ducking bar, and two ducker tiles. DUCKER: push to switch the ducker on or off. The stored depth is kept.DUCK DEPTH: turn for 1 dB per step, -60 dB to -0.5 dB. It readsOFFwith a grey LED while the ducker is switched off, and turning it does nothing then. Switch the ducker on withDUCKERfirst.
Without the permission the two ducker tiles are not on the page. The page needs Channel Config to be on. Threshold and timing cannot be changed on the :kontroller, they stay with the engineer in KLANG:app. The :kontroller has no EQ for the ambience mic either, that stays an engineer setting in KLANG:app.
Where to see the ducker working
CONFIG > INFO, blockAMBIENCE DUCKER:off, or the current settings and a lineAmbience Mic: worst <x> dB(the strongest ducking since the :kontroller started) withducking <x> dB NOWornot ducking.METERscreen: a gain reduction overlay on the ambience mic meter. The meter itself shows the mic before the ducker, so it does not dip while ducking. Only the overlay moves.AMB/AUXpage of the :kontroller: the ducking bar described above.
Safety limiter
What it does
The safety limiter is a brickwall limiter at the very end of the :kontroller’s outputs. It is hearing protection: if a faulty device anywhere upstream fires a full-scale burst, the limiter catches it before it reaches the musician’s ears. It is on by default with a ceiling that keeps the output below a set level and is transparent for any normally levelled mix.
- The headphone output is protected whenever the limiter is on.
- The XLR and Dante outputs are protected while they are routed from
Post EQ(the default). OnCONFIG > ROUTINGthat source readsPost EQ+Dyn. For the other routings (for exampleAux In,Amb MicorPre Master) the limiter is bypassed on that output. - The ceiling is the output level in dBFS.
- The limiter sees the left and right side together, so the stereo image does not shift when only one side limits.
- The limiter settings belong to the :kontroller, not to a mix. They are stored on the unit and survive a restart.
- Ratio (brickwall) and attack are factory values and cannot be changed.
Headphone Gain step of the :kontroller (-12 dB, 0 dB, +12 dB) acts after the limiter: with the same ceiling, +12 dB is 24 dB louder in the ears than -12 dB. See Known limits.Setting it up in KLANG:app
Requires Admin Mode. On CONFIG > CONNECT, section Safety Limiter:
| Setting | What it does | Values |
|---|---|---|
Limiter | Switches the safety limiter off to hear the mix without it. It is on by default and meant to stay on. | on/off, default on |
Ceiling (dBFS) | Nothing leaves the output above this level. Same setting as the master fader. | -40 dBFS to 0 dBFS in steps of 0.5 dB, default -1 dBFS |
Release (ms) | How long the limiter takes to let go again. Short is transparent on peaks and can pump on dense material, long is steady but holds the level down after a loud moment. | 1 ms to 1000 ms, default 75 ms |
Soft Knee | Lets the limiter start working just below the ceiling instead of exactly at it. Gentler on dense material, less exact about the ceiling. | on/off, default off |
Limiter Defaults | Reset puts the ceiling and the tuning behind it back to the factory settings. The Limiter switch stays as it is, so a limiter you switched off to compare stays off. | button |

The master fader is the ceiling
While KLANG:app is connected to a :kontroller, the master fader at the right edge of the window controls the limiter ceiling instead of a mix volume. It is drawn in the warning colour so that it cannot be taken for a volume fader. The value is sent while you drag and is stored on the unit.
- Drag the fader down to lower the ceiling.
+and-step the ceiling by the channel gain step.- Click the dB value to type a ceiling (-40 dBFS to 0 dBFS).
- The overlay growing down over the output meters shows the current gain reduction, with a peak-hold line.
On the :kontroller
By default only the engineer can change the limiter. Switch on CONFIG > SETTINGS > UI Settings > Musician May Adjust Limiter (also in CONFIG > INFO > Set Menu, and on the :kontroller itself as Limiter Control under CONFIG > Options) to hand the ceiling to the :kontroller. The on/off switch, release and soft knee always stay with the engineer.
- On the
AMB/AUXpage pressCONFIG. The tiles that have a page readEDIT. - Push the third tile (the mix master). The master page opens with
BACKand theLIMITERtile with an orange LED. - Turn the
LIMITERtile to change the ceiling by the gain step. The dB value shows while turning. A hatched bar grows from the right as the ceiling comes down (2 dB per pixel, like the level bars). BACKandCONFIGreturn to theAMB/AUXpage withEDITstill on.
- There is no on/off switch for the limiter on the :kontroller. It is the safety net, switching it off stays with the engineer.
- The page always shows the limiter of this :kontroller, also while it follows another processor.
- It also works without a connected processor: then the third tile reads
MIX NOT foundand the unit-meters tile (the fourth) readsEDITand opens the limiter page. The page also stays reachable whenChannel Configis locked; then it is the only tile that readsEDIT. - Without the permission the
LIMITERtile is not on the master page.

LIMITER tile on the master edit page of the :kontroller.Where to see the limiter working
CONFIG > INFO, blockOUTPUT LIMITER: the ceiling, how long the limiter has been watching, and eithernever engagedor the number of episodes with the worst gain reduction, the time spent above 3, 6 and 12 dB, the last episode andREDUCING NOWwhile it works.NOT ACTIVE on the headphone outputmeans the limiter does not protect the headphone output at the moment, for example because it is switched off.METERscreen: a gain reduction overlay on the output meters. The headings of the input rows and the output rows carryPRE-DYNandPOST-DYN, so you can tell which side of the dynamics stages you are looking at. The overlays for the limiter and the ducker only appear for a :kontroller that has the stage.
Safety limiter in demo mode
In demo mode KLANG:app runs a safety limiter of its own behind the mix. In Admin Mode the Safety Limiter section on CONFIG > CONNECT sets it, and the METER screen shows its gain reduction. The master fader stays the mix volume. There is no ducker in demo mode.
Letting the musician adjust the stages
Both permissions are off by default and are device settings of the :kontroller. They are included in the clone functions for :kontrollers.
| Permission | Where to set it | What it unlocks on the :kontroller |
|---|---|---|
Musician May Adjust Limiter | CONFIG > SETTINGS > UI Settings, also CONFIG > INFO > Set Menu and Limiter Control on the unit | The ceiling on the LIMITER tile of the master page. |
Musician May Adjust Ducker | CONFIG > SETTINGS > UI Settings, also CONFIG > INFO > Set Menu and Ducker Control on the unit | The DUCKER and DUCK DEPTH tiles on the AMB MIC page. |
The presets of Mix UI Presets set both permissions: on in Full Mixing Access, off in Only Group Mixing and Channel Mixing + Save/Load Menu. After applying a preset, check the two switches if you want a different combination.
Known limits for testers
- The limiter is a digital protection, not an exposure limit. The analog
Headphone Gainstep (-12 dB, 0 dB, +12 dB; default -12 dB; onCONFIG > SETTINGS > Audio & Boostand on the :kontroller asPhones GainunderCONFIG > Options) acts after the limiter. The musician can reach it on the unit with the default settings, because the local config menu is available by default and a long press onAMB/AUXre-opens it. There is no password on the unit. Only the digital over is contained. - Both digital boosts are inside the limiter’s reach.
Ambience Mic Boostacts before the limiter and the ducker chain,Digital Mix Boost(+12 dB) acts on the whole mix before the limiter. Both are onCONFIG > SETTINGS > Audio & Boost, and on the :kontroller asAmbMic BoostandDigital BoostunderCONFIG > Options, so the musician can reach both while the local config menu is available. - No look-ahead. Onset overshoot of about 1 ms is expected, see the warning above.
- The ceiling goes down to -40 dBFS. The master fader, a typed dB value, the :kontroller’s
LIMITERtile and the rowCeiling (dBFS)onCONFIG > CONNECTall cover -40 dBFS to 0 dBFS. A lower ceiling stored on the unit by an earlier preview build is shown as -40 dBFS and only changes when you move one of these controls. - If you tested an earlier 6.1 preview build: the ceiling used to act about 6 dB early (the output was held about 6 dB below the set ceiling). That is fixed, the number now means the real output level. A ceiling stored by the earlier build is not converted, so such a unit limits 6 dB later than it did. Check the ceiling after updating.
- The ducker meter does not dip. The ambience mic meter shows the mic before the ducker on purpose. Look at the overlay, the bar on the :kontroller or the INFO screen to see the ducking.
- The ducker listens to the Dante input only. It does not react to the Aux input. The right threshold depends on the gain structure of the installation, so test with a hot and with a conservative console feed.
- An output carrying only the ambience mic is ducked too. There is no un-ducked ambience send.
- The ducker settings are per mix, the limiter settings per unit. After a :kontroller follows another processor, the limiter shown is still the local one, the ducker is the one of the mix.
- Defaults are starting points. Ducker depth, threshold and timing have not been tuned by ear across many rooms yet. Reports about what works for your band are welcome.
What to test
- Ducker: switch
Duckeron (factory depth -12 dB), play music on the Dante input and confirm the ambience drops, the bar shows on the :kontroller and the overlay onMETERmoves. Stop the music and confirm the ambience comes back smoothly. - Ducker: switch
Duckeroff during ducking and confirm the ambience returns without a jump. Switch it on again and confirm the depth you had is still there. - Ducker: save a personal preset, change the depth, load the preset, restart the :kontroller and confirm the settings come back each time.
- Limiter: lower the ceiling on the master fader until the overlay appears, confirm
OUTPUT LIMITERonCONFIG > INFOcounts episodes, then pressLimiter DefaultsResetand confirm the ceiling returns to its factory default while theLimiterswitch stays as it was. - Limiter: route an XLR or Dante output from a source other than
Post EQand confirm that output is no longer limited, and that the headphone output still is. - Permissions: switch each permission on, change the value on the :kontroller, and confirm the app shows the new value. Switch the permission off and confirm the tiles disappear.